Air Refueling Archive

Huge Collection of Air Refueling Pictures

KC-10 Boom On A KC-135

A Lockheed C-5A moves into pre-contact behind a NKC-135A that has been fitted with the Advanced Aerial Refueling Boom designed for the KC-10. Click photo to enlarge.

A Lockheed C-5A moves into pre-contact behind a NKC-135A that has been fitted with the Advanced Aerial Refueling Boom designed for the KC-10. Click photo to enlarge.

In this rare picture, a Lockheed C-5A Galaxy is seen behind an NKC-135A that has been fitted with a KC-10 boom. The advanced fly by wire boom was attached to the NKC-135 during the KC-10’s development to test the handling characteristics.

The KC-10 boom consists of two aerodynamically faired tubes, one telescoping within the other.  The telescoping tube is supported by rollers within the outer tube. A fixed tube is located inside the telescoping tube. A sliding seal provides passage of fuel without leakage. The boom is attached to the tanker by a gimbal unit. The boom is free to move throughout the operating envelope. A fuel line swivel and flexible fuel line provide passage of fuel from the aerial refuel system across the boom pitch and roll axis through the fixed tube at the forward end of the boom. A surge boot running the entire length of the telescope tube dampens fuel surges during coupled flight or disconnect. The surge boot is pre-charged with dry nitrogen or air.

The boom flight control actuation system is an integrated closed-loop, fly-by-wire system utilizing a boom control unit with fail-passive fault monitoring and self-test features.

The boom flight control actuation system consists of the boom control unit, an elevation/roll hand controller, linear and rotary position transducers, accelerometers, nozzle load sensors, elevator and rudder actuators, a boom controller force selector, annunciator lights, and switches. A status/test panel is provided for displaying built-in-test information from the boom control unit.

The boom control surfaces consist of two fin/rudder assemblies attached to the elevator tips. The elevator is attached to the fixed tube by a combined hinge/actuator fitting. Boom positioning (elevation and roll) during free-flight is accomplished through the use of the elevation/roll hand controller, commonly referred to as the boom flight control stick. The boom operator uses the boom flight control stick to make inputs to move the boom, the boom control unit interprets these inputs and sends the appropriate signals to the actuators of the control surfaces. During coupled flight, an automatic load alleviation system (ALAS) is automatically activated to minimize nozzle radial loads by trimming the boom control surfaces to track the receiver aircraft position during coupled flight. While in contact, the boom operator monitors the system and guards the boom flight control stick, taking necessary actions when needed. Axial loads are also automatically limited by the telescoping system.

The boom operator selects the proper disconnect limits and telescope-at-disconnect switch positions during preparations for contact operations. Once a receiver aircraft is in the proper position within the refueling envelope, and alignment of the boom nozzle and receiver is achieved, the boom is extended to insert the nozzle into the receptacle. When insertion is completed, the control system advances to the coupled mode. The ALAS mode, if preselected, is automatically actuated. Automatic disconnects occur if preselected limits are exceeded. If preselected, automatic retraction occurs at the time of disconnect.

Receiver tracking/nozzle load alleviation is accomplished through two methods: couple flight control law logic and ALAS. coupled flight control laws are active anytime the flight controls are in the COUPLED  mode. ALAS is active anytime the ALAS switch displays ENABLED and the flight control system is in COUPLED mode. The flight control system can be advanced to COUPLED bye establishing a contact;  pressing the contact made TEST switch; or pulling and holding EMER CONTACT MADE switch. The flight control system also advances to COUPLED whenever sustained nozzle loads greater than 500 pounds are experienced; however, ALAS is not active during this condition.

The COUPLED mode of the flight control system is designed to partially alleviate nozzle loads and allow the boom to follow receiver movements. Receiver tracking/nozzle load alleviation is accomplished by utilizing boom position information to generate commands to back drive the flight control stick to approximate boom position in relation to the receiver. Boom operator assistance may be required to minimize loads to an acceptable level.

Air refueling is accomplished with ALAS ON unless the system malfunctions. Receiver tracking/nozzle load alleviation is accomplished through the detection of nozzle loads by the nozzle load sensor assembly and back driving the flight control stick to align the boom with the receiver. ALAS maintains nozzle loads at an acceptable level without boom operator assistance.

However, the boom operator can override ALAS. It takes approximately one second after contact is established or the EMER CONTACT MADE switch is pulled to transition the flight control laws from FREE FLIGHT to COUPLED logic, and to back drive the boom flight control stick to correspond with boom  position. After once second; ALAS is turned on, the stick shaker is armed, the stick forces are increased to their maximum value and the COUPLED light comes on. The increased stick forces and stick shaker are designed to reduce inadvertent boom operator inputs to the flight control system when ALAS is active. Moving the flight control stick form its commanded position as little as 4º activates the stick shaker which vibrates/shakes the boom flight control stick.

ALAS continues to alleviate nozzle loads after a disconnect is initiated (DISC light on) until the selected RCVR DISC DELAY time setting; at that point, the COUPLED light goes off, ALAS ceases to alleviate nozzle loads, the stick shaker is deactivate, the control stick forces return to their selected values, the controller back drive is frozen in the last commanded position for two seconds and the flight control laws start transitioning from COUPLED to FREE FLIGHT over a one second period.

An ALAS failure is indicated by the ROLL ALAS INOP and/or ELEVATION ALAS INOP light illuminating. The two axes are independent of each other and receiver tracking and stick shaker continue to function in the operation axis. Both the coupled flight control law logic back drive and ALAS are inoperative when a failed stick condition exists. Failure of the flight control stick is indicate by: the ROLL ALAS INOP and/or Elevation ALAS INOP light(s) illuminating, a five second audible tone in the boom operator’s headset, and the boom flight control stick going limp in the failed axis.

Th telescopic actuation system provides extension and retraction of the telescoping tube during freeflight and controls receiver’s push/pull forces in the coupled mode. The system consists of a telescoping tube, a closed loop chain-cable drive, a hydraulic servo motor, two telescope control sticks, a position indicator, and annunciator light. Telescope control is provided through two telescope control sticks; one each at the boom operator’s and instructor boom operator’s  position. Each stick extends or retracts the boom; however, commands from the instructor’s stick overrides inputs from the boom operator’s position.

The independent disconnect system (IDS) is an electrically controlled, pneumatically actuated system located in the nozzle assembly. Pneumatic pressure is supplied from a compressed air reservoir mounted on the telescope tube. The IDS is operated by depressing the disconnect switch through the second detent. When the system is activate, pneumatic pressure reacts the toggle latches on each side of the nozzle to a flush position. This allows the boom to be retracted from the receiver aircraft while its toggles are in the latched/extended position. The toggle latches have a holding circuit installed that retains them in the retracted position after IDS actuation, until the RESET TO READY button is pushed.

Under various designations, including NC-135A, NKC-135A and NKC-135E, NASA and the U.S. Air Force operate a fleet of heavily-modified C-135 airframes as aerial testbeds. The type of work performed by these aircraft is greatly varied, but includes refueling tests with new aircraft types, airborne laser trials, weightlessness training for astronauts, and numerous programs involving the testing of airborne equipment and space technology.


Image Source:

May 11, 2009 - Posted by | 1970s, Boom Pod View, C-5, KC-10, KC-135, KC-135A, Uncategorized, Unsourced Images | , ,

No comments yet.

Leave a Reply

Fill in your details below or click an icon to log in: Logo

You are commenting using your account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

%d bloggers like this: